Question: How do I hook up my tattoo gun?

How do you set up a tattoo gun for beginners?

1:295:26TATTOO MACHINE SETUP as a beginner step by stepYouTubeStart of suggested clipEnd of suggested clipSo to set it up all you need to do is grab the grip. And the tube. Slide the tube there into theMoreSo to set it up all you need to do is grab the grip. And the tube. Slide the tube there into the grip tighten that up then grab the tip. Put that into the grip. There tighten that up grab.

How do you hook up power to a tattoo gun?

Plug in the power supply. Plug the foot pedal into the tattoo power supply. Attach the clip cord to the face of the tattoo power supply unit. Attach the prongs of the clip cord to the upper and lower binding posts of the tattoo gun, near the coils. Press the foot pedal to test the machine.

How do I setup my tattoo gun?

2:545:21Tattoo Machine Setup - Needle and Tube - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have the needle in the tube. Pick up your machine. And slide the tube with the opening andMoreOnce you have the needle in the tube. Pick up your machine. And slide the tube with the opening and the tip facing upwards up through the vise grip.

What do I need for a tattoo setup?

For a good start, your tattooing supplies should always include needles, tubes, tips, and grips, ink, a machine, stencil products, and a power supply. The right tattooing equipment can get you started with creating beautiful works that will please your customers.

How do I start tattooing myself?

Sterilize your equipment.Sterilize your needle. Just before you plan to give yourself a tattoo, drop your needle in a pot of water and boil it for five minutes. Pour your ink cleanly. Use less ink than you think youll need. Put on clean rubber gloves.

What angle do you hold a tattoo gun?

Use a standard angle between 45 and 60゚ to put color into the skin. Most people work in small tight circles, but with mags, I have found that a Box Motion works better than circles.

How many volts should my tattoo shader be?

Six volts is appropriate for lining. Most tattoo artists adjust voltage by listening carefully to the sound of the gun--it should produce a steady buzz or a hum.

Why is my tattoo gun not working?

If your machine just wont work at all, you probably have an open in your circuit or a shortage. You want to make sure all your points are clean at first. The circuit will break if there is something caught between them. To open the contact hold the armature bar down with your thumb and blow hard on the points.

How do you outline a tattoo for beginners?

1:2011:18HOW TO TATTOO - LINE WORK - YouTubeYouTube

What happens if you slap your new tattoo?

Suggested Tattoo Aftercare -DO NOT let anyone touch or slap your healing tattoo. Dirty hands cause infection. Slapping it can blow out the lines. -DO NOT scratch or scrub your healing tattoo.

Is it OK to slap an itchy tattoo?

-As your tattoo is healing it might begin to scab and itch. Its extremely important to not pick, scratch, or peel your tattoo! If your tattoo is itchy you can lightly slap it or apply an ice pack. -Your skin will peel and flake as it heals, some of which will be color tinted.

Is it harder to tattoo yourself?

If you do your own tattoo youll most likely only scratch the surface. The proper tattooing process penetrates 1/16th of an inch into your skin. When doing the tattoo on your own, a lack of experience not to mention your own pain receptors will keep you from going as deep as you need to.

How far should the needle be out on a tattoo gun?

The tip of the needle should not be sticking out anymore than 2mm and no less than 1mm. Keep in mind that every persons skin type is different and there is no exact measure. If during your tattoo there are excessive amounts of blood, it is obviously going in too deep.

Why is the ink not taking in tattoo?

One cause of ink not going in is: Needle is set too far out for that viscosity ink. The tip is the reservoir for the ink. Thick slowly-flowing inks cannot travel as far as thinner inks so hanging the needle way out will prevent the ink flowing such a long distance.

Contact us

Find us at the office

Cudd- Lehnert street no. 7, 84569 New Delhi, India

Give us a ring

Esly Garzone
+76 910 442 603
Mon - Fri, 10:00-16:00

Contact us